VectorLinux

Please login or register.

Login with username, password and session length
Advanced search  

News:

Visit our home page for VL info. For support and documentation, visit the Vector Linux Knowledge Center or search the Knowledge Center and this Forum using the search box above.

Author Topic: Already use pppoe , still can not browse web  (Read 1682 times)

zjkhere

  • Member
  • *
  • Posts: 8
Already use pppoe , still can not browse web
« on: April 13, 2009, 03:12:01 am »

I've just installed VL6.0 std
pppoe-status seems ok ,  but can not browse any web page
Logged

bigpaws

  • Vectorian
  • ****
  • Posts: 1869
Re: Already use pppoe , still can not browse web
« Reply #1 on: April 13, 2009, 05:00:45 am »

You can test DNS to see if that sis setup correctly.

Open a terminal and type:

ping -c 5 yahoo.com

If there is no response try:

ping -c 5 68.180.206.184

That is the address for yahoo.com and see if you get a response.

If there is a response by using the ip address and not the name then
it is a DNS issue. To fix it edit as root /etc/resolv.conf and add the
ip address of your ISP.

If there is no response at all then look at ifconfig to see that there
is an address on interface ppp0.

Bigpaws
Logged

zjkhere

  • Member
  • *
  • Posts: 8
Re: Already use pppoe , still can not browse web
« Reply #2 on: April 13, 2009, 05:47:58 am »

If there is no response at all then look at ifconfig to see that there
is an address on interface ppp0.

Bigpaws

How to see the address by looking at inconfig?
Logged

rbistolfi

  • Packager
  • Vectorian
  • ****
  • Posts: 2305
Re: Already use pppoe , still can not browse web
« Reply #3 on: April 13, 2009, 07:26:29 am »

Run the ifconfig command in a terminal as root and paste the output here.
Logged
"There is a concept which corrupts and upsets all others. I refer not to Evil, whose limited realm is that of ethics; I refer to the infinite."
Jorge Luis Borges, Avatars of the Tortoise.

--
Jumalauta!!

zjkhere

  • Member
  • *
  • Posts: 8
Re: Already use pppoe , still can not browse web
« Reply #4 on: April 14, 2009, 07:08:24 pm »

It work now

I don't why it worked , I guess it's my mistakes cause the problem

thank you all for helping

ifconfig is here
eth0      Link encap:Ethernet  HWaddr 00:10:5c:ec:7a:94 
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:4583 errors:0 dropped:0 overruns:0 frame:0
          TX packets:4144 errors:0 dropped:0 overruns:0 carrier:0
          collisions:1907 txqueuelen:1000
          RX bytes:5186955 (4.9 MiB)  TX bytes:571096 (557.7 KiB)
          Interrupt:18 Base address:0xc000

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

ppp0      Link encap:Point-to-Point Protocol 
          inet addr:60.181.213.152  P-t-P:61.174.191.33  Mask:255.255.255.255
          UP POINTOPOINT RUNNING NOARP MULTICAST  MTU:1492  Metric:1
          RX packets:4552 errors:0 dropped:0 overruns:0 frame:0
          TX packets:4112 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:3
          RX bytes:5084851 (4.8 MiB)  TX bytes:478621 (467.4 KiB)
Logged